Chapter 1: Introduction
Chapter 2: PMMC Type Instrument
Chapter 3: EDM Type Instrument
Chapter 4: M.I Type Instrument
Chapter 5: Energy And Power Measurement
Chapter 6: Energy Meter
Chapter 7: Rectifier Type Instrument
Chapter 8: Electrostatic Type Instrument
Chapter 9: CRO
Chapter 10: AC Bridge
Chapter 11: Measurement Of Resistance
Chapter 12: Transducer
Chapter 13: Instrument Transformer
Chapter 14: Error Analysis
Chapter 15: Unit And Dimension
Chapter 16: Miscellaneous
Chapter 17: -Indicating Instrument
Chapter 18: -Measurement of Power and Energy
Chapter 19: - CRO
Chapter 20: - Instrument Transformer
Chapter 21: - Measurement of Resistance & Bridge
Chapter 1: Introduction
Chapter 2: Basic of Electric Circuit Theory
Chapter 3: Concept of Super Mesh & Super Nodal
Chapter 4: BCTQ Set - 1
Chapter 5: BCTQ Set - 2
Chapter 6: Network Theorem
Chapter 7: A.C Circuit
Chapter 8: BCTQ Set - 3
Chapter 9: BCTQ Set - 4
Chapter 10: Resonance
Chapter 11: Two Port Network
Chapter 12: BCTQ Set - 5
Chapter 13: Transient Analysis
Chapter 14: Magnetically Coupled Circuit
Chapter 15: Graph Theory
Chapter 16: Locus Diagram
Chapter 17: Filter
Chapter 1: Basic Principal of Electrical Machine
Chapter 2: Basic Principal Of Electrical Machine And Transformer
Chapter 3: Three Phase Induction Machine
Chapter 4: BCTQ Set - 1
Chapter 5: BCTQ Set - 2
Chapter 6: Single Phase Motors
Chapter 7: Synchronous Machine
Chapter 8: BCTQ Set - 3
Chapter 9: BCTQ Set - 4
Chapter 10: DC Mchine
Chapter 11: - Basic Principal Of Electrical Machine
Chapter 12: BCTQ Set - 5
Chapter 13: - Transformer
Chapter 14: -3 Phase Induction Machine
Chapter 15: -Single Phase Motors
Chapter 16: - DC Machine
Chapter 17: - Synchronous Machine
Chapter 1: Introduction of Power System & Generation of Electrical Energy
Chapter 2: Introduction
Chapter 3: Introduction of Power System.
Chapter 4: Generation of Electrical Energy.
Chapter 5: BCTQ Set - 1
Chapter 6: Economics and operating factor
Chapter 7: Mechanical design of overhead lines / Tariff /Power improvement
Chapter 8: BCTQ Set - 2
Chapter 9: Economics and operating factor.
Chapter 10: Transmission Line Parameters.
Chapter 11: BCTQ Set - 3
Chapter 12: Underground cable
Chapter 13: Fault Analysis
Chapter 14: BCTQ Set - 4
Chapter 15: Performance of Transmission Line.
Chapter 16: Supply System.
Chapter 17: BCTQ Set - 5
Chapter 18: Distribution system
Chapter 19: Switch gear and protection
Chapter 20: Mechanical design of overhead lines.
Chapter 21: Distribution system.
Chapter 22: miscellaneous
Chapter 23: Switch gear and protection.
Chapter 24: Underground cable.
Chapter 25: Power System Stability.
Chapter 26: miscellaneous.
Chapter 27: WORK BOOK
Chapter 1: Semiconductor Physics
Chapter 2: Electronic Device
Chapter 3: Semiconductor Diode & Application
Chapter 4: Transistor
Chapter 5: FET & MOSFET
Chapter 6: Oscillator
Chapter 7: Small Signal & large signal Amplifier and feedback amplifier
Chapter 8: Rectifier
Chapter 1: Introduction
Chapter 2: Power Electronics
Chapter 3: Power Semiconductor Device
Chapter 4: Converter
Chapter 5: Chopper
Chapter 6: Cycloconverter
Chapter 7: AC Voltage Regulator
Chapter 1: BCTQ Set - 1
Chapter 2: Introduction of Control System
Chapter 3: Block Diagram Reduction Technique
Chapter 4: BCTQ Set - 2
Chapter 5: BCTQ Set - 3
Chapter 6: Signal Flow Graph
Chapter 7: Time Response Analysis
Chapter 8: BCTQ Set - 4
Chapter 9: Stability
Chapter 10: Root Locus Technique
Chapter 11: Frequency Response Analysis
Chapter 12: Bode Plot
Chapter 13: Polar Plot
Chapter 14: Nyquist Plot
Chapter 15: miscellaneous Topics
Chapter 1: BCTQ Set - 1
Chapter 2: illumination
Chapter 3: Source of light
Chapter 4: Electrolysis
Chapter 5: Cell and Battery
Chapter 6: Electric Traction
Chapter 7: Electric Heating
Chapter 8: Basic Electric Welding
Chapter 1: Estimation & Costing
Chapter 2: Work Book
Chapter 1: Basic Introduction
Chapter 2: Arc Welding Processes
Chapter 3: Resistance Welding Processes
Chapter 4: Chemical Welding Processes
Chapter 5: Soldering & Brazing
Chapter 6: Welding Defects
Chapter 1: Logic Gate
Chapter 2: Combinational
Chapter 3: Sequential
Chapter 4: Number system
Chapter 1: Chapter-1 (Introduction)
Chapter 2: Chapter-2 (Architecture of 8085)
Chapter 3: Chapter-3 (Instruction Set & Data Formats)
Chapter 4: Chapter-4 (Interrupts)
Chapter 5: Chapter-5 (Interfacing )
Chapter 1: Electrostatics
Chapter 2: Magnetostatics
Chapter 3: maxwell Equations
Chapter 4: Electromagnetic Wave
Chapter 5: Incidence of EM Wave
Chapter 1: Introduction
Chapter 2: Classification of signals
Chapter 3: Different operation of signals
Chapter 4: Classification of systems
Chapter 5: Fourier Series
Chapter 6: Transforms in Signal & Systems
Chapter 7: miscellaneous
Chapter 1: Amplitude Modulation
Chapter 2: Frequency Modulation
Chapter 1: Introduction
Chapter 2: Polarization
Chapter 3: Dielectric loss
Chapter 1: BCTQ
Chapter 1: MOVING IRON (English)
Chapter 2: Error Analysis (English)
Chapter 3: PMMC (Hindi)
Chapter 4: Transformer (Hindi)
Chapter 5: BCTQ Set - 1
Chapter 6: BCTQ Set - 2
Chapter 7: BCTQ Set - 3
Chapter 8: BCTQ Set - 4
Chapter 9: BCTQ Set - 5
Chapter 1: B.Tech
Chapter 2: Diploma
Chapter 1: Power system
Chapter 2: SIGNAL SYSTEM
Chapter 3: EMFT
Chapter 4: MICROPROCESSOR
Chapter 5: Power Electronics
Chapter 6: EMI
Chapter 7: EDC
