Why is gear
teeth made harder?
गियर के दांतों को सख्त क्यों बनाया जाता है?
The
efficiency in case of worm gear drives is generally in the range of
वर्म गियर ड्राइव के मामले में दक्षता आम तौर पर की सीमा में होती है
Lewis
equation in spur gear design applied to
स्पर गियर डिज़ाइन में लुईस समीकरण लागू किया गया
Identify the wrong statement about a single plate clutch from the
following.
निम्नलिखित में से सिंगल प्लेट क्लच के बारे में गलत कथन को पहचानें।
Which of the
following method is CORRECT for increasing the torque transmitting capacity of
the clutch?
क्लच की टॉर्क संचारण क्षमता बढ़ाने के लिए निम्नलिखित में से कौन सी विधि सही है?
Which of the following statement is CORRECT about the wet clutch?
गीले क्लच के बारे में निम्नलिखित में से कौन सा कथन सही है?
Which of the
following is TRUE about the torque transmitting capacity of the conical clutch?
शंक्वाकार क्लच की टॉर्क संचारण क्षमता के बारे में निम्नलिखित में से कौन सा सत्य है?
Which of the
following theory is used in the design of clutches when friction linings are
new?
जब घर्षण लाइनिंग नई होती है तो क्लच के डिजाइन में निम्नलिखित में से किस सिद्धांत का उपयोग किया जाता है?
The outer
cone of the conical clutch is keyed to the ________ shaft and inner cone is
________ to slide axially.
शंक्वाकार क्लच का बाहरी शंकु ________ शाफ्ट से जुड़ा होता है और आंतरिक शंकु अक्षीय रूप से स्लाइड करने के लिए ________ होता है।
Which of the
following statement is CORRECT about the dry clutch?
ड्राई क्लच के बारे में निम्नलिखित में से कौन सा कथन सही है?
Which of the
following clutch also considered as the wet clutch?
निम्नलिखित में से किस क्लच को गीला क्लच भी माना जाता है?
In the
disc-clutch the clutch acts as a ________ .
डिस्क-क्लच में क्लच ________ के रूप में कार्य करता है।
Which of the
following is known as a positive clutch?
निम्नलिखित में से किसे पॉजिटिव क्लच के रूप में जाना जाता है?
The equation
for the calculation of torque transmitting capacity in the conical clutch as
per uniform wear theory is ________ .
निम्नलिखित में से किस सिद्धांत का उपयोग क्लच के डिजाइन में किया जाता है, जब घर्षण अस्तर खराब हो जाते हैं?
Which of the
following theory is used in the design of clutches, when the friction linings
get worn out?
निम्नलिखित में से किस सिद्धांत का उपयोग क्लच के डिजाइन में किया जाता है, जब घर्षण लाइनिंग खराब हो जाते हैं?
Which of the
following theory is used for the determination of torque capacity in cone
clutch?
शंकु क्लच में टॉर्क क्षमता के निर्धारण के लिए निम्नलिखित में से किस सिद्धांत का उपयोग किया जाता है?
Which of the
following statement is INCORRECT about the dry clutch and wet clutch?
ड्राई क्लच और वेट क्लच के बारे में निम्नलिखित में से कौन सा कथन गलत है?
When the friction lining is new, the wear varies ________ .
जब घर्षण लाइनिंग नया होता है, तो घिसाव ________ भिन्न होता है।
The pressure
distribution in the uniform wear theory is ________ .
एकसमान घिसाव सिद्धांत में दबाव वितरण ________ है।
The uniform
pressure theory as compared to the uniform wear theory gives________ .
एकसमान घिसाव सिद्धांत की तुलना में एकसमान दबाव सिद्धांत ________ देता है।
The device
which permits the connection and disconnection of shaft is :
वह उपकरण जो शाफ्ट के कनेक्शन और वियोग की अनुमति देता है:
Which of the
following statements is not true for couplings?
कपलिंग के लिए निम्नलिखित में से कौन सा कथन सत्य नहीं है?
The inner and
outer radius of friction surface of a plate clutch are 50 mm and 100 mm
respectively. What is the ratio of maximum intensity of pressure to minimum
intensity of pressure on clutch plate if magnitude of axial force is 4kN?
Assume uniform wear theory
एक प्लेट क्लच की घर्षण सतह की आंतरिक और बाहरी त्रिज्या क्रमशः 50 मिमी और 100 मिमी है। यदि अक्षीय बल का परिमाण 4kN है तो क्लच प्लेट पर दबाव की अधिकतम तीव्रता और दबाव की न्यूनतम तीव्रता का अनुपात क्या है? एक समान घिसाव का सिद्धांत मान लें
Assertion (A): A clutch is the best means to connect a driving shaft for regular power transmission
Reason (R):A
clutch can be frequently engaged and disengaged at operators will
अभिकथन (A): नियमित विद्युत संचरण के लिए ड्राइविंग शाफ्ट को जोड़ने के लिए क्लच सबसे अच्छा साधन है
कारण (R): ऑपरेटर की इच्छा पर क्लच को बार-बार जोड़ा और हटाया जा सकता है
Which of the
following clutches is positive type?
निम्नलिखित में से कौन सा क्लच पॉज़िटिव प्रकार का है?
Crowning of a pulley is done to
चरखी की क्राउनिंग किसके लिए की जाती है?
The pulley,
which is used to increase the angle of contact, is called a/an ________ pulley.
चरखी, जिसका उपयोग संपर्क के कोण को बढ़ाने के लिए किया जाता है, को ________ चरखी कहा जाता है।
If the angle
of contact is 3.06 rad and the coefficient of friction between the smaller
pulley surface and belt is 0.5, calculate the tension (in N) in the slack side,
if the tension in the tight side is 1200 N.
यदि संपर्क का कोण 3.06 रेडियन है और छोटी चरखी सतह और बेल्ट के बीच घर्षण का गुणांक 0.5 है, तो स्लैक पक्ष में तनाव (N में) की गणना करें, यदि तंग पक्ष में तनाव 1200 N है।
Which of the following factors plays a considerable role in choice of
belt drives
निम्नलिखित में से कौन सा कारक बेल्ट ड्राइव की पसंद में महत्वपूर्ण भूमिका निभाता है
The ratio of
the tension in the tight side
बेल्ट के टाइट साइड T1 में तनाव और बेल्ट T2 के स्लैक साइड में तनाव का अनुपात 5.0 है। यदि बेल्ट के तंग हिस्से पर तनाव 5000 N है और बेल्ट का वेग 25.00 m/sec है, तो बेल्ट द्वारा प्रेषित शक्ति (kW) क्या है?
The correct
option for the occurrence of the total slip in a drive occurs when _____
किसी ड्राइव में कुल स्लिप की घटना के लिए सही विकल्प तब होता है जब _____
The tension
of the tight side and the slack side of belt are T1
बेल्ट के टाइट साइड और स्लैक साइड का तनाव रैखिक वेगv के साथ क्रमशः T1 और T2 है। बेल्ट द्वारा प्रेषित अधिकतम शक्ति के लिए कौन सा अभिव्यक्ति सबसे उपयुक्त है?
If the speed at which the belt can transfer the maximum power is 30 m/s
and the mass of the belt per meter length is 0.6 kg/m, determine the maximum,
tension (in N) produced in the belt.
यदि जिस गति से बेल्ट अधिकतम शक्ति स्थानांतरित कर सकता है वह 30 मीटर/सेकेंड है और प्रति मीटर लंबाई बेल्ट का द्रव्यमान 0.6 किलोग्राम/मीटर है, तो बेल्ट में उत्पन्न अधिकतम तनाव (N में) निर्धारित करें।
Which of the
following is the CORRECT reason for the creep in a belt drive?
बेल्ट ड्राइव में रेंगने का सही कारण निम्नलिखित में से कौन सा है?
If there is
no slip and the creep in the transmission, then what is the equation for the
velocity ratio in the open belt drive?
यदि ट्रांसमिशन में कोई स्लिप और क्रीप नहीं है, तो ओपन बेल्ट ड्राइव में वेग अनुपात के लिए समीकरण क्या है?
What is the
effect of slip of the belt on the velocity ratio of belt drive?
What is the velocity ratio for creep in the belt drive system for be σ1 being the stress in tight side, σ2 being the stress on slack side and E is the young’s modulus of elasticity of the belt material?
बेल्ट ड्राइव सिस्टम में क्रीप के लिए वेग अनुपात क्या है क्योंकि σ1 टाइट साइड में तनाव है, σ2 स्लैक साइड में तनाव है और E बेल्ट सामग्री की प्रत्यास्थता का यांग मापांक है?
The power
transmission takes place from a pulley of diameter 1 m running at the speed of
250 rpm to a pulley of 2.50 m diameter by means of a belt. Determine the speed
(in rpm) of the driven pulley?
शक्ति संचरण एक बेल्ट के माध्यम से 250 आरपीएम की गति से चलने वाली 1 मीटर व्यास वाली चरखी से 2.50 मीटर व्यास वाली चरखी तक होता है। चालित चरखी की गति (आरपीएम में) निर्धारित करें?
A pulley is
driven by a flat and the maximum tension produced in the belt is of 1400 N. The
belt has the density of 1000kg/m2
एक चरखी एक फ्लैट द्वारा संचालित होती है और बेल्ट में उत्पन्न अधिकतम तनाव 1400 N होता है। बेल्ट का घनत्व 1000kg/m2, 100 मिमी चौड़ा और 5 मिमी मोटा होता है। अधिकतम शक्ति के लिए बेल्ट की गति (एम/सेकंड) क्या है?
In skew bevel
gears, the axes
तिरछे बेवल गियर में, अक्ष
The part of
the tooth between the pitch circle and dedendum circle is called
पिच सर्कल और डेडेंडम सर्कल के बीच के दांत के भाग को कहा जाता है
In a belt drive, the condition where there is relative motion between
the belt and the pulley surface is known as
बेल्ट ड्राइव में, वह स्थिति जहां बेल्ट और पुली सतह के बीच सापेक्ष गति होती है, कहलाती है
Wire ropes
are used for applications experiencing
निम्न अनुप्रयोगों के लिए तार रस्सियों का उपयोग किया जाता है
Which type of
chain is used in motor cycle?
मोटर साइकिल में किस प्रकार की चेन का प्रयोग किया जाता है?
In a
horizontal flat belt drive, it is customary to use
क्षैतिज फ्लैट बेल्ट ड्राइव में, इसका उपयोग करना प्रथागत है
In a V-belt drive, the belt makes contact at ________.
वी-बेल्ट ड्राइव में, बेल्ट ________ पर संपर्क बनाता है।
The power
transmitted by a belt is maximum when the maximum tension in the belt compared
to centrifugal tension is ________ .
बेल्ट द्वारा संचारित शक्ति अधिकतम होती है जब केन्द्रापसारक तनाव की तुलना में बेल्ट में अधिकतम तनाव ________ होता है।
In V-belt
drive, belt touches________ .
वी-बेल्ट ड्राइव में, बेल्ट ________ को छूती है।
In a multiple
V belt drive, when a single belt is damaged, it is preferable to change the
complete set to ________ .
मल्टीपल वी बेल्ट ड्राइव में, जब एक बेल्ट क्षतिग्रस्त हो जाती है, तो पूरे सेट को ________ में बदलना बेहतर होता है।
The horse power transmitted by a belt is dependent upon
एक बेल्ट द्वारा प्रेषित अश्वशक्ति पर निर्भर है
A. Tension on
tight side of belt
B. Tension on
slack side of belt
C. Radius of
pulley
D. Speed of
pulley