The included angle for the V-belt is usually
वी-बेल्ट के लिए शामिल कोण आमतौर पर होता है
The power
transmitted by a belt is maximum when the maximum tension in the belt compared
to centrifugal tension is.
बेल्ट द्वारा संचारित शक्ति अधिकतम तब होती है जब बेल्ट में अपकेंद्रीय तनाव की तुलना में अधिकतम तनाव होता है।
Fan belt in automobiles is
ऑटोमोबाइल में फैन बेल्ट है
Which one of
the following drives is used for transmitting power without slip?
निम्नलिखित में से किस ड्राइव का उपयोग बिना स्लिप के बिजली संचारित करने के लिए किया जाता है?
Creep in belt drive is due to
बेल्ट ड्राइव में क्रीप किसके कारण होता है?
Tension in
the tight side of a belt drive is 100 N and that in the slack side is 60 N. If
the belt breadth is 10 cm and thickness is 4 cm, what is the maximum stress
induced in the belt
एक बेल्ट ड्राइव के टाइट साइड में तनाव 100 N है और स्लैक साइड में 60 N है। यदि बेल्ट की चौड़ाई 10 सेमी और मोटाई 4 सेमी है, तो बेल्ट में प्रेरित अधिकतम तनाव क्या है?
The sum of the
tensions when the belt is running on the pulley is
जब बेल्ट चरखी पर चल रही हो तो तनाव का योग है
The angle of V-belts is
वी-बेल्ट का कोण है
Mass per unit
length of belt of an open belt drive is 1.5 kg/m. If the linear velocity of the
belt is 10 m/s and radius of driving pulley 0.5 m, centrifugal tension in the
belt is
एक खुली बेल्ट ड्राइव के बेल्ट की प्रति इकाई लंबाई का द्रव्यमान 1.5 किग्रा/मीटर है। यदि बेल्ट का रैखिक वेग 10 मीटर/सेकेंड है और चरखी चलाने की त्रिज्या 0.5 मीटर है, तो बेल्ट में केन्द्रापसारक तनाव है
The
difference in tensions on the tight and slack side of a belt drive is 3000 N.
If the belt speed is 15 m/sec, the transmitted power is
एक बेल्ट ड्राइव के टाइट और स्लैक साइड पर तनाव का अंतर 3000 N है। यदि बेल्ट की गति 15 मीटर/सेकंड है, तो संचरित शक्ति है
For a flat
open-belt drive, the belt speed is 880m/min and the power transmitted is 22.5
kW.
एक फ्लैट ओपन-बेल्ट ड्राइव के लिए, बेल्ट की गति 880 मीटर/मिनट है और प्रेषित शक्ति 22.5 किलोवाट है। बेल्ट ड्राइव के टाइट साइड और स्लैक साइड टेंशन के बीच क्या अंतर है?
An idler
pulley is used :
एक आइडलर चरखी का उपयोग किया जाता है:
For
maximum power transmitted by belt, the maximum permissible tension in the belt
is
बेल्ट द्वारा प्रेषित अधिकतम शक्ति के लिए, बेल्ट में अधिकतम अनुमेय तनाव है
Creep
in belt is due to
बेल्ट में क्रीप किसके कारण होता है?
Creep
in a belt occurs due to
बेल्ट में क्रीप किसके कारण होता है?
In
belt drives the centrifugal tension
बेल्ट ड्राइव में अपकेंद्रीय तनाव होता है
Which is the correct option for the stress experienced by the shaft when the power transmission in shaft takes place through the gears?
जब शाफ्ट में विद्युत संचरण गियर के माध्यम से होता है तो शाफ्ट द्वारा अनुभव किए जाने वाले तनाव के लिए सही विकल्प कौन सा है?
A key made from a cylindrical disc having segmental cross-section, is known
as
खंडीय अनुप्रस्थ काट वाली बेलनाकार डिस्क से बनी कुंजी को कहा जाता है
Feather keys are generally ________.
फीदर चाबियाँ आम तौर पर ________ होती हैं।
The
key will fail in which of the following manner?
कुंजी निम्नलिखित में से किस तरीके से विफल हो जाएगी?
Which
of the following key transmits power through frictional resistance only?
निम्नलिखित में से कौन सी कुंजी केवल घर्षण प्रतिरोध के माध्यम से शक्ति संचारित करती है?
Metal
to metal joint is used for applications subjected to ________ .
धातु से धातु जोड़ का उपयोग ________ के अधीन अनुप्रयोगों के लिए किया जाता है।
The
sleeve or muff coupling is designed as a ________ .
स्लीव या मफ कपलिंग को ________ के रूप में डिज़ाइन किया गया है।
Which of the following steel key is usually strong in failure by shear
and crushing?
निम्नलिखित में से कौन सी स्टील कुंजी आमतौर पर कर्तन और क्रूसिंग से विफलता में मजबूत होती है?
In
the flange coupling the two flanges are coupled together by means of bolts fitted
in
फ्लैंज कपलिंग में दोनों फ्लैंज लगे हुए बोल्ट के माध्यम से एक साथ जुड़े होते हैं
Shaft
is subjected to which of the following stresses?
शाफ्ट निम्नलिखित में से किस तनाव के अधीन है?
The key shown in the figure below is
नीचे चित्र में दिखाई गई कुंजी है
Which
of the following key is under compression rather than in being shear when under
load?
निम्नलिखित में से कौन सी कुंजी लोड होने पर अपरूपण के बजाय संपीड़न में होती है?
For a key to be equally strong in shear and crushing the width of the key(assuming allowable crushing stress equal to twice of shear stress) should be
एक कुंजी के कतरनी में समान रूप से मजबूत होने और कुचलने के लिए कुंजी की चौड़ाई (कतरनी तनाव के दोगुने के बराबर स्वीकार्य कुचलने वाले तनाव को मानते हुए) होनी चाहिए
The pitch value in the specification Tr 40 × 14 (P7) of multiple start trapezoidal thread is :
मल्टीपल स्टार्ट ट्रैपेज़ॉइडल थ्रेड के विनिर्देशन Tr 40 × 14 (P7) में पिच मान है:
A
bench vice has following type of threads
एक बेंच वाइस में निम्नलिखित प्रकार के चूड़ी होते हैं
The rivet head shown in following figure is ________ head rivet
.
निम्नलिखित चित्र में दिखाया गया रिवेट हेड ________ हेड रिवेट है
The
crest-diameter of a screw thread is same as ________ .
एक स्क्रू थ्रेड का शिखर -व्यास ________ के समान होता है।
The
efficiency of self-locking screw is ________ .
सेल्फ-लॉकिंग स्क्रू की दक्षता ________ है।
Which
of the following is trapezoidal thread?
निम्नलिखित में से कौन सा समलम्बाकार चूड़ी है?
For
a screw, the angle of helix (a)
एक स्क्रू के लिए, हेलिक्स का कोण (α) लीड (L) और माध्य स्क्रू थ्रेड व्यास (d) से संबंधित है
Acme
threads are generally used in
एक्मे धागे का प्रयोग आम तौर पर किया जाता है
The
main part of the rivet does not involve which of the following part?
पिवोट के मुख्य भाग में निम्नलिखित में से कौन सा भाग शामिल नहीं है?
The types of failure involve in the analysis of the riveted joints are
रिवेटेड जोड़ों के विश्लेषण में शामिल विफलता के प्रकार हैं
1.
Shear failure of the rivet
2.
Tensile failure of the plate
3. Crushing failure of the plate
Which
of the following statements are is correct for the analysis of the riveted
joints?
रिवेट जोड़ों के विश्लेषण के लिए निम्नलिखित में से कौन सा कथन सही है?
Type
of riveted joint shown in the figure below is ________ .
नीचे दिए गए चित्र में दिखाए गए रिवेट जोड़ का प्रकार ________ है।
Plug
weld joint is used
Plug weld joint is used
Plain and butt weld may be used on materials upto approximately
लगभग तक सामग्री पर सादा और बट वेल्ड का उपयोग किया जा सकता है
Joggled
welded joints are used
जॉगल्ड वेल्डेड जोड़ों का उपयोग किया जाता है
Aircraft
body is usually fabricated by
विमान की बॉडी आमतौर पर किसके द्वारा निर्मित की जाती है?
The
distance between the centers of the rivets in adjacent rows of zigzag riveted
joint is known as ________ .
ज़िगज़ैग रिवेट जोड़ की आसन्न पंक्तियों में रिवेट्स के केंद्रों के बीच की दूरी को ________ के रूप में जाना जाता है।
Welding
units operate at what power factor?
वेल्डिंग इकाइयाँ किस शक्ति कारक पर कार्य करती हैं?
A riveted joint may fail due to
एक रिवेटेड जोड़ किसके कारण विफल हो सकता है?
A.
Shearing of the rivet
B.
Shearing of the plate at an edge
C.
Crushing of the rivet
If
the tearing efficiency of a riveted joint is 60% then ratio of the rivet hole
diameter to the pitch of rivets is ________ .
यदि किसी रिवेट जोड़ की फाड़ने की क्षमता 60% है तो रिवेट छेद के व्यास और रिवेट की पिच का अनुपात ________ है।
A
backing ring is used inside the pipe joint when making a ________ .
________ बनाते समय पाइप जोड़ के अंदर एक बैकिंग रिंग का उपयोग किया जाता है।
The rivet head for general purpose shown in the figure below is
सामान्य प्रयोजन के लिए रिवेट हेड नीचे चित्र में दिखाया गया है