A simply supported beam carries a concentrated load at its mid span. Another identical beam B carries the same load but uniformly distributed over the whole span. The ratio of maximum deflection of beam A to beam B will be

Offsets in surveying are

The shape of the bending moment diagram over the length of a beam, carrying a uniformly distributed load is always

Due to water logging of an area:–

Which of the seasoning method is adopted for the rapid seasoning of timber on large scale to obtain any desired moisture content?

The ratio of elongations of a conical bar due to its own weight and that of a prismatic bar of the same length, is

The most economical section in bending is

Which of the following is commonly used as retarder in cement?

Which one of the following is used as a carrier in paint?

According to Indian standards, the number of raingauge stations for an area of 5200 km² in plains should be

A load P is applied to a wire of diameter d. If the radius of a wire is doubled and reduced the load to half, then its Young's modulus will be

Which crops does not come under kharif crops?

For complete hydration of cement, water–cement ratio needed is

Calculate the internal angle (degree) for the anallactic telescope.

The constant vertical distance between two adjacent contours, is known as :

Dimensions of coefficient of transmissibility are

A beam of length (L + 2a) has supports 'L' aparts with an overhang 'a' on each side. The beam carries a concentrated load 'W' at each end. The shear force between the two supports is given by:

With an increase in the supply of irrigation water, yields of the crops

Thickness of Plastering is usually:

A given material has young's modulus E, modulus of rigidity G and poisson's ratio 0.25. The ratio of young's modulus to rigidity of this material is: 

Total latitude of a point is positive if it lies

Calculate the year's purchase for a property of useful life of 30 years and rate of interest of 5% per annum.

Which of the following statements is correct?

Total Kjeldahl nitrogen is a measure of

The Bowditch method of adjusting a traverse is based on the assumption that Where e₁ and e₂ are erros in linear and angular measurements respectively and L is the length of a line.

In surveyor compass, 90° is written at

In route surveys, the most suitable method of contouring is:

Match the following:
        A         
    A. Carcinogenic agents    
    B. Dust Particles      
    C. Odour nuisance      
    D. Chronic pulmonary diseases
        B
    1. Cancer
    2. Respiratory diseases
    3. Bronchitis    
    4. Hydrogen sulphide

 

A    B    C    D

The velocity distribution over half of a cross section is uniform and is zero over the remaining half. The momentume correction factor for this cross section is-

The question consists of two statements; one labelled as 'Assertion' (A) and the other as 'Reason' (R)
    Assertion (A) : For mixed traffic conditions, the superelevation should fully counteract  the centrifugal force for the full design speed
    Reason (R) : Superelevation needed to main-tain the design speed in fully may exceed the limiting value 0.07. Further, as it is not possible to increase the radius, the speed has to be restricted.
    Examine above two statements carefully and select the correct answer from the option given below: 

What is the exceptional gradient in plain terrain?

Which one of the following velocity fields represents a possible fluids flow?

Average approximate value of delta for Cotton is

The covered area of a proposd building is 150m2 and it includes a rear courtyard of 5m × 4m. If the prevailing plinth area rate for similar buildings is Rs 1,250/m². What is its cost (in Rs)

Considering the velocity as one of the flow characteristics, which of the following expression can be written for one-dimensional unsteady flow?

If a tension member is subjected to axial and bending moment, then

The expected time (t_e) of a PERT activity in terms  of optimistic times (t_o), pessimistic time (t_p) and most likely time (t_m) is given by

To get the corresponding long wall and short wall lengths, we must ______one breadth to the centre line length and ______ one breadth from the centre line length respectively.

As per the general rules for the measurement of a building, all works shall be measured subject to certain tolerances. In this regard ‘the thickness of RCC slab’ shall be measured to the nearest

In limit state method, balanced design of a reinforced concrete beam gives:

Which command allows you to 'stretch an object'?

If a rectangular under-reinforced section is subjected to bending moment equal to its moment carrying capacity and the stress in steel and extreme compression fiber of concrete at this moment are σ_s and σ_c respectively then which of the following is correct ? Where, f_y and f_c are the permissible stresses in steel and concrete respectively.

Which of the following is not correctely matched?

A loose, natural sand deposit has a saturated unit weight of 19.3 kN/m³ and an angle of internal friction of 29°. The water table is at the ground surface. The total at–rest lateral earth pressure at a depth of 10 m is most nearly :
(Given sin29° = 0.485)

Which function key is used to 'turn ON and turn OFF polar tracking' in AutoCAD ?

The slope deflection equation at B of element BC in the following frame is (AB = 6 m and BC = CD = 8 m)

The distribution factor for the members OA, OB and OC are

         

The variation of bending moment along the length of central column of the frame shown in figure is:

Clockwise moments are applied to both the ends of a uniformly simply supported beam. If the ratio of the rotation of two ends is 2, then the ratio of the applied moments will be :

For the section shown in the figure, the neutral axis lies at: