The main reason for water pollution of Luni river is
लूनी नदी के जल प्रदूषण का मुख्य कारण है
In which of the following districts of Rajasthan, Dravyavati river is facing problems related to water pollution?
राजस्थान के निम्नलिखित जिलों में से किसमें, द्रव्यवती नदी जल प्रदूषण से संबंधित समस्याओं का सामना कर रही है?
If we travel along the Luni River from its origin to its end, in what order will we find its tributaries?
(A) Jawai
(B) Bandi
(C) Sukri
(D) cavity
Code-
यदि हम लूनी नदी के किनारे इसके उद्गम से अंत तक यात्रा करते हैं, तो हम इसकी सहायक नदियों को किस क्रम में पायेंगे?
(A) जवाई
(B) बाण्डी
(C) सूकड़ी
(D) गुहिया
कूट-
Which of the following rivers flows through Jaipur district?
निम्न में से कौन सी नदी जयपुर जिले में होकर प्रवाहित होती है?
Jakham river is not a tributary of-
जाखम नदी एक सहायक नही है-
Which of the following flows in Toravati basin?
निम्नलिखित में से तोरावाटी बेसिन में कौनसी प्रवाहित होती है?
Which of the following (river origin place) is not matched?
निम्नलिखित में से कौनसा (नदी-उत्पत्ति स्थान) सुमेलित नहीं है?
Which of the following rivers does not flow in Udaipur district?
निम्नलिखित में से कौन सी नदी उदयपुर जिले में प्रवाहित नहीं होती है?
The highest percentage of Banganga river basin is located in the district.
जिले में बाणगंगा नदी बेसिन का सर्वाधिक प्रतिशत भाग स्थित है।
Which of the following tributary of Luni River does not originate from the Aravalli Hills?
निम्नांकित में से कौन-सी लूनी नदी की सहायक नदी अरावली पहाड़ियों से उद्गमित नहीं होती है?
The name of the river flowing through Bikaner district is-
बीकानेर जिला से प्रवाहित होने वाली नदी का नाम है-
Which of the following (river-related districts) is not matched?
निम्नलिखित में से कौनसा (नदी-सम्बन्धित जिला) सुमेलित नहीं है?
Consider the following advantages with
respect to HVDC transmission :
1.
Long distance transmission
2. Low cost of transmission
3. Higher efficiency
Which of the above advantages are correct?
Light triggering is mainly used in
Load-flow solution is essential for :
In a single phase system of supply, which of the following is used to
test the supply correctly?
In transmission of bulk electrical power, high voltage offers :
Which software provides automation electrical power system?
Which of the following is NOT a design of
substations?
A metal clad switchgear having barriers of
insulating is_________.
In substations, the breaker maintenance is
provided in the
In a multi machine interconnected system, subsequently to a 3-phase fault, the
transient stability is examined by
In a 3-phase, 5 kV, 5 MVA system, what is
the base impedance?
In an n-bus power system, considering
n-nodes network, the size of 
is
The voltage of a particular bus can be controlled by controlling
the_________.
Consider two buses corrected by an impedance of 
and bus-2 voltage is 
. The real and reactive power supplied by bus-1,
respectively, are
The size of bus admittance matrix for the sing line diagram shown in the
figure is________.
In a power system there are 50
buses
Slack bus = 1
Generator buses = 8
Load buses = 41
By
Newton- Raphson method, the size of the jacobian matrix =_________.
Select the wrong statement from the following in relation to power flow
analysis
Load
frequency controllers are carried out with
For formation of the Y bus matrix (using node voltage analysis) in power
system network modeling is used
Steady state stability of a power system is improved by
In Gauss-Seidel load flow method, the number of
iterations may be reduced if the correction in voltage at each bus is
multiplied by
In a power system network, At which bus, the shunt is connected that can be
known from
For a graph of power system network shown in the figure below, where bus
numbers and impedances are marked, assuming equal R/X of impedances,
find
the bus impedance matrix element
The 
matrix is a sparse
matrix because :
Load flow studies must be made on a power system before
In
G-S method of power flow problem, the number of iterations
What is the form of the 
matrix for carrying
out load flow studies by Gauss-Se method of a power system having mesh
connection of nodes?
For load flow studies, what are the
quantities specified at load bus?
The
per unit value of a
Which of the following quantities are normally specified at the voltage
controlled bus for a load flow solution?
Which one of the following statements is correct?.
The elements of each row of a 
matrix for load flow
studies in power
system add up to zero.
A sample power system network is shown in the figure given below. The
reactances marked are in p.u. What is the pu value of
matrix
Consider the following statements in respect of load flow studies in power system :
1. Bus admittance matrix is a sparse matrix
2. Gauss-Seidel method is preferred over Newton Raphson method for load
flow studies
3. One of the buses is taken as slack bus in load flow studies Which of these
statements are correct?
Consider the following quantities :
1. Real power
2. Reactive power
3. Power factor
4. Input current
5. Bus voltage magnitude
6. Bus voltage phase-angle
For the purpose of the load flow studies of a power system, each bus or
node is associated with which one of the combination of the above four
quantities?
A bus bar is rated by
A equipment has an impedance of 0.9 pu to a base of 20 MVA, 33 kV. To
the base of 50 MVA, 11 kV, the pu impedance will be
The
The distribution substation mounted on a utility pole is called as :